DENAIR Compressor Logo

Tel : 0086 21 3783 1829

E-mail : info@www.benphil.com

Home > VSD Air Compressor > Two Groups PM VSD Screw Air Compressor (55-250 kW)

Two Groups PM VSD Screw Air Compressor (55-250 kW)

Two Groups PM VSD Screw Air Compressor (55-250 kW)

Two Groups PM VSD Screw Air Compressor Freatures and Advantages:


01 Features Of permanent Magnet Variable Frequency Air Compressor

  • Ultra-low temperature rise design, which allows the compressor running at ultra-low frequency for a long time.
  • Closed-loop vector control system for faster control and more precise speed control.
  • The compressor unit can still operate efficiently when the frequency is reduced by more than 50%.
  • The pressure is stable and the pressure fluctuation is accurately controlled within 0.1 bar.
  • The figure shows a comparison of several starting methods. It can be seen that the frequency converter is slowly accelerated to start, the starting is more stable, and the current peak is completely avoided.
PM VSD Two-stage Screw Air Compressor

02 Air End

  • More stable, no mechanical transmission failure: high-efficiency permanent magnet synchronous motor and screw male rotor adopt embedded-integrated shaft direct connection structure, no gear transmission, completely eliminate gear pitting or broken teeth; Two independent permanent magnet motors are integrated directly drive two air ends, no coupling failures.
  • More energy efficient, the air end is always running at energy-saving speed.
  • More efficient and efficient permanent magnet motor + no transmission efficiency loss.
  • More comfortable, low running noise, eliminating three sources of noise: no-click bearing noise, no gear meshing noise, no coupling drive noise.
  • More compact: The permanent magnet motor is small in size and the integrated structure saves space.
  • Under the set frequency conversion pressure, the unit will automatically adjust to keep the output pressure within ± 0.1 bar, reducing unnecessary waste (the power consumption increases by 7% for every 1 bar of pressure increase)
PM VSD Two-stage Screw Air Compressor

03 Advantages of Permanent Magnet Motors Compared to General Asynchronous Motors

  • High efficiency: Eliminates excitation system losses and improves efficiency.
  • It is still efficient under low load conditions: the energy efficiency of a permanent magnet motor is more than 9% higher than that of a conventional asynchronous motor at full load operation, and its energy efficiency remains unchanged as the speed decreases.
  • Large overdrive torque: The ratio of the maximum starting torque of the permanent magnet synchronous motor to the rated torque can be more than 3 times, while the general asynchronous motor is only 1.6 times.
  • The control is more stable: the corresponding time of the permanent magnet motor is <50ms, and the gas production can be adjusted in a large range in an instant, so that the gas pressure is truly stable.
PM VSD Two-stage Screw Air Compressor

04 Stainless Steel Piping Design

  • The piping arrangement is simple and beautiful. Stainless steel piping design to effectively prevent rust in the pipeline, and avoid safety accidents caused by leakage of the pipeline.
PM VSD Two-stage Screw Air Compressor

05 More Advanced Technology. More Powerful Inverter

  • The standard equipment is equipped with a high-frequency reactor to reduce the high frequency generated by the inverter.
  • The soft start of the inverter reduces the peak current at startup, resulting in a smooth start and greatly reduced power costs.
  • Forced cooling of the inverter to prevent high temperature shutdown in Summer.
  • Standard equipment dust screen, circuit board surface coating treatment, high efficiency and durability against dirt, dust, moisture.
  • The special design of the heat dissipation area of the inverter ensures stable operation of the inverter under high temperature environment.
  • No idling occurs under any load conditions to achieve the desired power saving effect.
  • Quickly track changes in pressure, control pressure fluctuations within ±0.1 bar, and optimize the use of the power to accurately provide the right amount of air as needed.
PM VSD Two-stage Screw Air Compressor

06 Oil Filter

  • The imported brand is used to reliably filter the dirt particles in the lubricating oil to ensure the smoothness and lubrication of the oil system at 0.1 micron.
PM VSD Two-stage Screw Air Compressor

07 Air Filter

  • The imported brand is used to reliably remove dirt from the air. The dust particles in the air are controlled below 0.3 microns and the filtration accuracy is as high as 99.99%.
PM VSD Two-stage Screw Air Compressor
Two Groups PM VSD Screw Air Compressor (55-250 kW) Technical Parameters:
Model Maximum working pressure Capacity(FAD) Installed
motor power
IP Grade Noise level Dimensions(mm) Weight Air outlet
pipe diameter
Starting
Method
EEI
bar(g) psig m3/min cfm kw hp (L) (W) (H) kg
DAV-55+ 7 102 6.46-12.93 228-457 55 75 IP54 75 1900 1500 1590 1500 DN50

Direct Driven
Air Cooling

EEI1
8 116 6.32-12.63 223-446
10 145 5.83-11.66 206-412
DAV-75+ 7 102 7.99-15.98 282-564 75 100 IP54 75 1900 1500 1590 1700 DN50
8 116 7.89-15.79 279-558
10 145 7.12-14.24 251-503
DAV-90+ 7 102 10.81-21.62 382-763 90 120 IP54 78 2650 1700 1850 2550 DN80
8 116 10.18-20.36 359-719
9 131 9.92-19.83 350-700
10 145 9.41-18.81 332-664
DAV-110+ 7 102 12.52-25.04 442-884 110 150 IP54 78 2650 1700 1850 2550 DN80
8 116 12.07-24.14 426-852
9 131 11.46-22.93 405-810
10 145 11.09-22.19 392-784
DAV-132+ 7 102 15.15-30.29 535-1070 132 175 IP54 78 2650 1700 1850 3100 DN80
8 116 14.53-29.06 513-1026
9 131 13.49-26.99 476-953
10 145 12.09-24.18 427-854
DAV-160+ 7 102 18.45-36.91 651-1303 160 215 IP54 80 3000 1950 2030 4000 DN100
8 116 17.63-35.26 623-1245
9 131 16.47-32.94 581-1163
10 145 15.72-31.44 555-1110
DAV-185+ 7 102 21.05-42.11 743-1487 185 250 IP54 80 3000 1950 2030 4300 DN100
8 116 19.79-39.58 699-1398
9 131 18.74-37.47 662-1323
10 145 17.89-35.79 632-1264
DAV-200+ 7 102 22.25-44.49 786-1571 200 270 IP54 85 3000 1950 2030 4700 DN100
8 116 21.31-42.61 752-1505
9 131 19.30-38.60 681-1363
10 145 17.85-35.71 630-1261
DAV-220+ 7 102 24.14-48.28 852-1705 220 300 IP54 85 3500 2200 2300 5000 DN125
8 116 23.91-47.82 844-1689
9 131 22.89-45.79 808-1617
10 145 20.42-40.83 721-1442
DAV-250+ 7 102 28.24-56.48 997-1994 250 350 IP54 85 3500 2200 2300 5500 DN125
8 116 26.54-53.08 937-1874
9 131 25.45-50.89 899-1979
10 145 23.00-46.00 812-1624

*) FAD in accordance with ISO 1217:2009, Annex C: Ansolute intake pressure 1 bar (a), cooling and air intake temperature 20℃
**) Nosie level as per ISO 2151 and the basic standard ISO 9614-2, operation at maximum operating pressure and maximum speed; tolerance:±3 dB(A)

Specifications are subject to change without prior notice

Two Groups PM VSD Screw Air Compressor (55-250 kW) Technical Parameters:
Model Maximum working pressure Capacity(FAD) Installed
motor power
IP Grade Noise level Dimensions(mm) Weight Air outlet
pipe diameter
Starting
Method
EEI
bar(g) psig m3/min cfm kw hp (L) (W) (H) kg
DAV-55+ 7 102 6.46-12.93 228-457 55 75 IP54 75 1900 1500 1590 1500 DN50

Direct Driven
Air Cooling

EEI1
8 116 6.32-12.63 223-446
10 145 5.83-11.66 206-412
DAV-75+ 7 102 7.99-15.98 282-564 75 100 IP54 75 1900 1500 1590 1700 DN50
8 116 7.89-15.79 279-558
10 145 7.12-14.24 251-503
DAV-90+ 7 102 10.81-21.62 382-763 90 120 IP54 78 2650 1700 1850 2550 DN80
8 116 10.18-20.36 359-719
9 131 9.92-19.83 350-700
10 145 9.41-18.81 332-664
DAV-110+ 7 102 12.52-25.04 442-884 110 150 IP54 78 2650 1700 1850 2550 DN80
8 116 12.07-24.14 426-852
9 131 11.46-22.93 405-810
10 145 11.09-22.19 392-784
DAV-132+ 7 102 15.15-30.29 535-1070 132 175 IP54 78 2650 1700 1850 3100 DN80
8 116 14.53-29.06 513-1026
9 131 13.49-26.99 476-953
10 145 12.09-24.18 427-854
DAV-160+ 7 102 18.45-36.91 651-1303 160 215 IP54 80 3000 1950 2030 4000 DN100
8 116 17.63-35.26 623-1245
9 131 16.47-32.94 581-1163
10 145 15.72-31.44 555-1110
DAV-185+ 7 102 21.05-42.11 743-1487 185 250 IP54 80 3000 1950 2030 4300 DN100
8 116 19.79-39.58 699-1398
9 131 18.74-37.47 662-1323
10 145 17.89-35.79 632-1264
DAV-200+ 7 102 22.25-44.49 786-1571 200 270 IP54 85 3000 1950 2030 4700 DN100
8 116 21.31-42.61 752-1505
9 131 19.30-38.60 681-1363
10 145 17.85-35.71 630-1261
DAV-220+ 7 102 24.14-48.28 852-1705 220 300 IP54 85 3500 2200 2300 5000 DN125
8 116 23.91-47.82 844-1689
9 131 22.89-45.79 808-1617
10 145 20.42-40.83 721-1442
DAV-250+ 7 102 28.24-56.48 997-1994 250 350 IP54 85 3500 2200 2300 5500 DN125
8 116 26.54-53.08 937-1874
9 131 25.45-50.89 899-1979
10 145 23.00-46.00 812-1624

*) FAD in accordance with ISO 1217:2009, Annex C: Ansolute intake pressure 1 bar (a), cooling and air intake temperature 20℃
**) Nosie level as per ISO 2151 and the basic standard ISO 9614-2, operation at maximum operating pressure and maximum speed; tolerance:±3 dB(A)

Specifications are subject to change without prior notice

Rotary Screw Air Compressor

Download

Diesel Portable Screw Air Compressor

Download

Oil-free Air Compressor

Download

Compressed Air Treatment Equipment

Download

You may Like:


Free Consultation:

If you are interested in DENAIR air compressor, please contact us via
email: info@www.benphil.com or send your inquiry in the form below.we will reply you within 24 hours.


*

*

*

Related Information:

Right Air Compressor
In our daily sales work, we have noticed that some of air compressor users dont really understand how to choose the right compressor specially if they are only responsible for purchase and finance departments...
Details
Read More >

DENAIR Compressor LOGO
Like us on Facebook Follow us on YouTube Follow us on Twitter Follow us on LinkedIn

© 必威软件下载